Godiag GT107 DSG Gearbox Adapter Support List, Connection and Pinouts

---

GT107 DSG Gearbox Adapter Kit is designed for Read/ Write GT107 DSG Gearbox (DQ250, DQ200, VL381, VL300, DQ500, DL501 etc.) with PCMtuner module 58/Kess V2/KTM Bench, etc.

Part 1. PCMtuner

1.Support List
Module 58
VAG DSG/CVT

DQ200MQB/G2 (0CW)
DQ250MQB (0D9)
Reading, Writing, Checksum correction

VL381/DL382 (0AW/0CK)
DL501/G2 (0B5)
DQ200 (0AM)
DQ250E/F (02E)
VL300/V30 (01J/0AN)
Writing, Checksum correction

DQ200/MQB/G2 Boot (EEPROM)
DQ250E/F/MQB Boot (EEPROM)
DL501/G2 Boot (EEPROM)
VL381 Boot (EEPROM)
DL382 Boot (EEPROM)
Honda UDCT Boot (Continental TC1782/EEPROM)
Reading, Writing

DQ200/MQB/G2 Boot (MICRO)
DQ250E/F/MQB Boot (MICRO)
VL381 Boot (MICRO)
DL501/G2 Boot (MICRO)
DQ500 (0BH/0BT)
VL300/V30 BSL (FLASH)
VL300/V30 BSL (EEPROM)
DQ250C (02E)
DL382 Boot (MICRO)
Honda UDCT Boot (Continental TC1782/MICRO)
Reading, Writing, Checksum correction

2.Connection Steps
1)On Bench

1.Connect Godiag GT107 to the gearbox ECU like VAG, DQ250, DQ200, VL381, VL300, DQ500,
DL501, for Renault DC0/DC4 Gen2 and Honda LUK UDCT.
2. Connect GT105 and connect 12V 2A DC power supply. (GT105 IMMO function keys must be
up.)
3.The GODIAG GT107 analog ignition switch is in “Auto” mode if it is not pressed, and in
"Manual" mode if pressed down(note: please select the corresponding mode in the software to
read data)
4. Connect PCMFlash, PCMTuner J2534passthru.
5.Perform data reading and writing operations.

2)On Vehicle

1.Connect Godiag GT107 to the gearbox ECU, VAG, DQ250, DQ200, VL381, VL300, DQ500, DL501
for Renault DC0/DC4 Gen2 and Honda LUK UDCT.
2.Connect the Godiag ECU IMMO Prog AD and connect the 12V vehicle battery.(The Godiag ECU
IMMO Prog AD’s IMMO button must be up.)
3.The Godiag GT107 analog ignition switch is in “Auto” mode if it is not pressed, and it is in “Manual”
mode if it is pressed down(Note: Please select the corresponding mode in the software for data
reading).
4.Connect PCMFlash, PCMTuner J2534passthru.
5.Perform data reading and writing operations.

3.Pinouts




Part 2. KessV2

1.Connection Steps
1)On Bench

1.Connect Godiag GT107 to gearbox ECU DQ250, DQ200, DQ500
2.Connect the Godiag ECU IMMO Prog AD with the vehicle battery or 12v 3A power supply (The Godiag ECU IMMO Prog AD’s IMMO button must be up.)
3.Connect kessv2 device, and press down the GT107 switch and it will be in “Manual” ignition
mode
4.Press down the 120 ohm resistor switch
5.Connect the computer and open the software to read and write data

2)On Boot

use a direct connection to the connector of the control UNIT, the switching power
supply is carried out either manually (recommended) or by using the scheme of automatic power
control, GODIAG GT107 DSG Gearbox Adapter (same PowerBox or converted from KESS). For manual control, the entrance to the boot mode may not happen on the first attempt.
*Read DQ500: only when connected directly!
Note: the power supply must be switched manually, while only the ignition must be switched on
or off (pin 15), the second contact must be connected constantly.


VL300 / V30 BSL
Requires drilling a single hole in the minimum diameter cap in order to insert a probe into it. The probe is connected to the GODIAG GT107 DSG Gearbox Data Adapter BOOT 1k ohm GND line(included in the GT107 host). It is mandatory to connect to-line and it is highly recommended to use auto power to quickly “feel” the pin on the board.


If you get interested in this item, please check below:
Godiag GT107 DSG Gearbox Adapter Kit User Manual